FortiGate Firewall Security Policy Audit

Policy-audit-driven analysis of FortiGate/FortiOS firewall policies. Unlike

generic firewall checklists that check for open ports and default-deny, this

skill evaluates the FortiOS-specific security architecture: Virtual Domain

(VDOM) segmentation, UTM profile binding on every allow policy, FortiGuard

signature freshness, and SD-WAN SLA-based traffic steering security

implications.

Covers FortiOS 7.x+ on FortiGate hardware appliances and FortiGate-VM virtual

instances. For FortiManager-managed deployments, the audit addresses ADOM

hierarchy and policy package consistency. Reference references/policy-model.md

for the full VDOM/UTM inspection chain and references/cli-reference.md for

read-only CLI commands.

When to Use

• Post-change policy review after rule additions or VDOM topology changes
• VDOM segmentation audit verifying inter-VDOM link isolation and per-VDOM policy independence
• UTM profile coverage assessment — finding allow policies without antivirus, IPS, or web-filter inspection
• SD-WAN security evaluation — confirming SLA violations do not steer traffic around security controls
• FortiGuard license and connectivity validation — ensuring signature databases are current
• HA cluster security posture check — verifying firmware parity, config sync, and session-sync settings
• Quarterly or annual compliance audit requiring per-policy justification
• Pre-upgrade baseline before FortiOS major version changes

Prerequisites

• Read-only administrative access to FortiOS CLI (or diagnose-level privilege for runtime state)
• Understanding of the VDOM topology — which VDOMs exist, their function (management, traffic, DMZ), and expected inter-VDOM links
• Knowledge of expected UTM profile assignments per policy category (internet-bound, inter-zone, intrazone)
• For FortiManager-managed environments: access to the ADOM with visibility into policy packages
• Awareness of SD-WAN configuration — SLA targets, member interfaces, and health-check definitions
• Running configuration committed — audit evaluates the active configuration, not pending changes

Procedure

Follow this audit flow sequentially. Each step builds on prior findings.

The procedure moves from VDOM architecture inventory through per-VDOM

rule-level analysis to UTM coverage, FortiGuard health, SD-WAN security,

and HA posture.

Step 1: VDOM Architecture Inventory

Collect all VDOMs and their roles.

config vdom
edit root
end
get system status

On a multi-VDOM system, list all VDOMs:

diagnose sys vd list

For each VDOM, record: name, type (traffic/management/admin), assigned

interfaces (physical and virtual), inter-VDOM link pairs, and VDOM resource

limits (session count, CPU quota). Identify the management VDOM — this

is where FortiGuard updates, logging, and administrative access are

configured.

Check inter-VDOM links:

show system vdom-link

Inter-VDOM links function as virtual interfaces connecting two VDOMs.

Traffic crossing a VDOM link is subject to the receiving VDOM's firewall

policies — verify that inter-VDOM traffic is not bypassing inspection.

Verify VDOM resource limits to detect unbounded VDOMs that could starve

other VDOMs during volumetric events:

config global
get system vdom-property

Flag any VDOM without explicit resource limits in a multi-VDOM deployment.

Step 2: Firewall Policy Rule-by-Rule Analysis

For each VDOM, retrieve the full policy table:

config vdom
edit <vdom-name>
show firewall policy

FortiOS evaluates firewall policies top-down by sequence number within each

VDOM. The first matching policy is applied. Evaluate each policy against

these criteria:

• Overly permissive policies: Policies with srcaddr "all",

dstaddr "all", service "ALL", and action accept are Critical

findings — they accept all traffic on all ports with no restriction.

• Missing UTM profiles: Allow policies without antivirus, web-filter,

application-control, or IPS profile binding pass traffic uninspected.

Check utm-status, av-profile, webfilter-profile,

application-list, and ips-sensor on each allow policy.

• Disabled policies: Policies with status disable still occupy

sequence numbers and create audit confusion. Flag for cleanup.

• Schedule-based policies: Policies with schedule other than always

may create time-window security gaps. Verify schedules align with

intended access windows.

• Implicit deny: FortiOS has an implicit deny (policy ID 0) at the

bottom of each VDOM's policy table. Verify it is logging traffic for

visibility into denied connections.

Check for unused policies using hit count data:

diagnose firewall iprope show 100004 <policy-id>

Policies with zero hits over 90+ days are cleanup candidates.

Step 3: UTM Profile Binding Audit

For each allow policy in every VDOM, verify that UTM inspection profiles

are bound. The goal is zero allow policies without threat inspection.

Check each allow policy for these profile bindings:

• Antivirus (av-profile): File-based malware scanning. Required on

all internet-bound and inter-zone policies.

• Web Filter (webfilter-profile): URL categorization and blocking.

Required on all policies permitting HTTP/HTTPS.

• Application Control (application-list): Application identification

and enforcement. FortiOS equivalent of App-ID.

• IPS (ips-sensor): Intrusion prevention signatures. Required on

all allow policies carrying untrusted traffic.

• Email Filter (emailfilter-profile): Anti-spam for SMTP/IMAP/POP3.

Required on email-carrying policies.

• DLP Sensor (dlp-sensor): Data loss prevention pattern matching.

Required where sensitive data egress risk exists.

• SSL Inspection (ssl-ssh-profile): Determines whether encrypted

traffic is decrypted for UTM inspection. Without SSL inspection set to

deep-inspection, AV and IPS see only connection metadata on HTTPS.

Summarize coverage: count allow policies with full UTM binding versus allow

policies with partial or no UTM profiles. Calculate the UTM coverage ratio.

Check the inspection mode per VDOM:

config vdom
edit <vdom-name>
get system settings | grep inspection-mode

Flow-based mode applies all UTM in a single pass (faster, less thorough).

Proxy-based mode buffers and inspects fully (more thorough, more resource

intensive). The mode affects which UTM features are available and their

efficacy.

Step 4: FortiGuard Service Validation

FortiGuard provides the signature databases that UTM profiles depend on.

Stale signatures reduce detection efficacy.

get system fortiguard-service status
diagnose autoupdate versions

Verify the following signature databases are current:

Check FortiGuard connectivity:

diagnose debug rating
execute ping service.fortiguard.net

If FortiGuard is unreachable, all cloud-dependent features (web filter

rating queries, FortiSandbox cloud, outbreak prevention) operate in

degraded mode using cached data only.

Verify the update schedule:

show system autoupdate schedule

Best practice is scheduled updates every 1–4 hours for AV and daily for

IPS/App-Control. Manual-only updates are a finding.

Step 5: SD-WAN SLA and Rule Security

If SD-WAN is configured, evaluate security implications of traffic steering.

config vdom
edit <vdom-name>
show system sdwan

Review SD-WAN components:

• SLA targets and health checks: Examine each health check definition

(protocol, server, threshold). Verify health-check servers are reachable

and meaningful for the SLA metric (latency, jitter, packet loss).

diagnose sys sdwan health-check

• SD-WAN rules: Each rule maps traffic to preferred WAN members based

on SLA status. Review rule priorities and the tie-break method.

diagnose sys sdwan service

• Fail-open behavior: When all SLA members fail, SD-WAN rules may fall

through to standard routing. Determine whether this fallback path still

traverses security inspection. A fail-open that routes around a security

VDOM or UTM-inspecting policy is a Critical finding.

• SD-WAN + firewall policy interaction: SD-WAN selects the egress

interface, but firewall policies still control access. Verify that

firewall policies cover all SD-WAN member interfaces. A policy that

references a specific interface may not match when SD-WAN steers traffic

to an alternate member.

Step 6: HA and Session Sync Audit

Evaluate HA cluster security posture.

get system ha status
diagnose sys ha checksum cluster

Check the following:

• HA mode: Active-passive (recommended for stateful firewalls) vs

active-active (requires careful session-sync configuration). Record

the mode and verify it matches design intent.

• Firmware parity: Both cluster members must run the same FortiOS

version. Version mismatch can cause session-sync failures and policy

inconsistencies.

diagnose sys ha checksum cluster

Compare configuration checksums between members. Mismatched checksums

indicate configuration drift — a security risk when policies differ

between HA members.

• Session sync configuration: Verify which session types are

synchronized (TCP, UDP, ICMP, expectation sessions). Unsynchronized

sessions drop during failover.

show system ha

Check session-pickup and session-pickup-connectionless settings.

• HA heartbeat security: Verify heartbeat interfaces use encryption

and authentication. Unencrypted heartbeats on shared network segments

are vulnerable to spoofing.

• HA management interface: Verify dedicated management access is

configured for each cluster member (ha-mgmt-interfaces) to ensure

both nodes remain independently accessible.

Threshold Tables

Policy Rule Severity Classification

UTM Coverage Maturity

Decision Trees

UTM Gap Remediation

Allow policy without UTM profiles
├── What traffic does this policy carry?
│   ├── Internet-bound → CRITICAL: Bind full UTM (AV+IPS+WebFilter+AppCtrl+SSL deep-inspection)
│   ├── Inter-VDOM or inter-zone → HIGH: Bind AV+IPS+AppCtrl minimum
│   ├── Intra-zone management → MEDIUM: Bind IPS+AppCtrl; AV optional
│   └── Monitoring/logging only → LOW: Evaluate if allow is needed
│
├── SSL inspection mode?
│   ├── certificate-inspection → UTM limited to metadata on HTTPS
│   │   └── Evaluate switching to deep-inspection for this policy
│   ├── deep-inspection → Full UTM efficacy on encrypted traffic
│   └── none → Only unencrypted traffic inspected
│       └── Add ssl-ssh-profile before UTM profiles
│
└── Inspection mode (VDOM-level)?
    ├── flow-based → Single-pass; good performance, some UTM features limited
    └── proxy-based → Full buffered inspection; verify resource impact
        └── Check CPU/memory: diagnose sys top

VDOM Consolidation Assessment

Multi-VDOM deployment evaluation
├── How many VDOMs are configured?
│   ├── >10 VDOMs → Evaluate consolidation; management complexity increases risk
│   ├── 3–10 VDOMs → Typical; verify each serves a distinct security function
│   └── 1–2 VDOMs → Minimal; verify VDOM is needed vs single-VDOM mode
│
├── Do all VDOMs have active policies?
│   ├── Empty or minimal policy VDOMs → Candidates for consolidation or removal
│   └── Active policy VDOMs → Verify traffic segmentation justification
│
├── Are inter-VDOM links necessary?
│   ├── Inter-VDOM traffic inspected by receiving VDOM → Correct architecture
│   └── Inter-VDOM traffic not inspected → Finding: add policies on VDOM links
│
└── Resource contention?
    ├── VDOM resource limits configured → Check utilization vs limits
    └── No limits → Set limits per VDOM to prevent starvation

SD-WAN Fail-Open Risk Evaluation

SD-WAN SLA failure scenario
├── All SLA members for a rule fail
│   ├── Rule has dst = security VDOM or UTM-inspecting path?
│   │   ├── Yes → Traffic falls to routing table
│   │   │   ├── Routing table path includes UTM inspection? → Acceptable
│   │   │   └── Routing table path bypasses UTM? → CRITICAL: fail-open gap
│   │   └── No → Standard egress; verify firewall policy still matches
│   │
│   └── SLA health-check server unreachable (false positive)?
│       ├── Single health-check server → HIGH: Add redundant check servers
│       └── Multiple servers, all down → Likely real outage; verify failover
│
└── Partial SLA failure (some members down)
    ├── Traffic steers to remaining members → Verify capacity
    └── Remaining member is a lower-security path → Evaluate risk

Report Template

FORTIGATE SECURITY POLICY AUDIT REPORT
========================================
Device: [hostname]
FortiOS Version: [version]
Platform: [FortiGate model / FortiGate-VM]
VDOM Mode: [multi-vdom / split-vdom / disabled]
Management: [standalone / FortiManager ADOM name]
Audit Date: [timestamp]
Performed By: [operator/agent]

VDOM ARCHITECTURE:
- VDOMs configured: [count]
- Management VDOM: [name]
- Inter-VDOM links: [count] ([list pairs])
- VDOMs with resource limits: [n] / [total]

PER-VDOM POLICY SUMMARY:
VDOM: [name]
  - Total firewall policies: [count]
  - Accept policies: [n] | Deny policies: [n]
  - Policies with full UTM profiles: [n] / [accept count]
  - Inspection mode: [flow-based / proxy-based]
  - SSL inspection (deep): [n] policies
  [Repeat for each VDOM]

FORTIGUARD STATUS:
- Connectivity: [connected / unreachable]
- AV signatures: [version] ([age])
- IPS signatures: [version] ([age])
- Web filter DB: [version] ([age])
- Application control DB: [version] ([age])
- Update schedule: [interval]

SD-WAN STATUS:
- SD-WAN enabled: [yes/no]
- SLA health checks: [count] ([all passing / N failing])
- Fail-open risk: [none identified / risk details]

HA STATUS:
- HA mode: [active-passive / active-active / standalone]
- Firmware parity: [matched / mismatched — versions]
- Config checksum: [matched / mismatched]
- Session sync: [enabled / disabled]

FINDINGS:
1. [Severity] [Category] — [Description]
   VDOM: [vdom-name]
   Policy ID: [id] (Seq: [sequence])
   Interfaces: [srcintf] → [dstintf]
   Issue: [specific problem]
   Current Config: [relevant policy fields]
   Recommendation: [specific remediation]

UTM COVERAGE:
- Per-VDOM coverage ratios: [list each VDOM: n/total (%)]
- Policies missing AV: [count]
- Policies missing IPS: [count]
- Policies missing web-filter: [count]
- Policies missing application-control: [count]

RECOMMENDATIONS:
- [Prioritized action list by severity]

NEXT AUDIT: [CRITICAL findings: 30d, HIGH: 90d, clean: 180d]

Troubleshooting

Large Multi-VDOM Deployments

Auditing more than 10 VDOMs manually is impractical. Export per-VDOM policy

tables via the FortiOS REST API (/api/v2/cmdb/firewall/policy?vdom=)

for programmatic analysis. Prioritize VDOMs carrying internet-bound or

inter-zone traffic — management VDOMs are lower risk.

FortiManager Policy Packages

In FortiManager-managed deployments, audit the installed policy on the

FortiGate (via show firewall policy), not just the FortiManager package —

local policies and installation state may differ. Use

diagnose fortimanager policy-check to identify discrepancies.

UTM Performance Impact

Before binding UTM profiles on high-throughput policies, assess headroom:

get system performance status
diagnose sys top 2 20

FortiGate models have rated throughput for NGFW and Threat Protection

profiles. Ensure traffic volume is within rated capacity. If constrained,

prioritize UTM on internet-bound policies and use flow-based inspection.

Firmware Upgrade Impact on Policies

FortiOS major upgrades may change UTM profile schema or deprecate features.

Export the policy baseline before upgrading, then post-upgrade verify:

UTM profile bindings preserved, policy sequence intact, SD-WAN rules

migrated, and HA cluster upgraded in sequence (secondary first).

Split-VDOM Mode vs Multi-VDOM Mode

Split-VDOM provides two VDOMs (root + FG-traffic); full multi-VDOM allows

custom count. Audit whether split-VDOM segmentation is sufficient for

compliance requirements. Changing VDOM mode requires a reboot.